Timber Doors

Guide · Homeowners · 4 min read · Updated 17 November 2026

Should You Repair or Replace a Timber Door? A Joiner's Checklist

Short answer

Most timber doors can be repaired if the rot is limited to the bottom rail, the joints are still sound and the door is not badly twisted. A repair or overhaul typically costs £150–£450, against £900–£1,800 for a new hardwood leaf or £1,600–£3,200 for a full door and frame. Replace when rot runs into the stiles and joints, the frame is failing, or the door can never be made secure or weathertight.

Should You Repair or Replace a Timber Door? A Joiner's Checklist

Common timber door problems

Timber doors tend to fail in predictable ways. Sticking and binding usually come from swollen edges after a wet spell, dropped hinges or a frame that has moved. Draughts come from flattened seals, worn weatherstrips or gaps that have opened up. Rot almost always starts low down, where rain collects on the bottom rail, the sill and the glazing beads.

Before deciding anything, a joiner will check how far each problem goes. Many doors that look tired simply need easing, rehanging, new seals and a fresh finish. Others are hiding deeper decay inside joints.

  • Door sticks or rubs the frame in wet weather
  • Visible gaps or daylight around the edges
  • Soft, spongy or darkened timber at the bottom rail
  • Paint or stain peeling and bare wood showing
  • Lock hard to turn or keeps not lining up
  • Glazing beads loose, rotten or letting water in

Repairs that work

Rehanging and easing is the simplest fix. Hinges are tightened or packed, screws replaced with longer ones into solid timber, and binding edges planed and resealed. Sealing the planed edge matters, because bare timber takes up moisture and swells again.

Splice repairs replace a rotten section with new timber of the same species, glued and fixed in place. A bottom rail can often be rebuilt this way. Resin repairs suit smaller areas: the decayed wood is cut back to sound timber, consolidated and filled with a flexible resin that is shaped and painted. Both methods keep the original door, which is especially worthwhile for period and listed properties.

Repair or replace: how to decide

The table gives a rough guide. A site visit will confirm the right option, because rot is often worse once the paint is opened up.

Cost is only one part of the decision. Think about what the door is worth to the house. An original panelled door with fine mouldings on a Victorian terrace is hard to replicate cheaply, so spending a little more on repair often makes sense even where replacement would cost about the same. A plain 1980s softwood door with a weak lock has little to keep, so the money is usually better spent on a new door set that is warmer and more secure. Also consider how the door will be used. A back door opening onto a wet, exposed garden takes more punishment than a front door under a deep porch, so a marginal repair may not last there.

What you seeLikely answerTypical cost
Sticking, dropped hinges, worn sealsRepair and adjust£150–£300
Small soft patch at bottom railResin or splice repair£200–£450
Rotten frame foot but sound doorFrame repair or new frameQuoted on inspection
Rot running into stiles and jointsReplace leaf£900–£1,800
Rotten door and frame, split sillReplace full door set£1,600–£3,200
Period door worth keepingRepair and refinish£150–£450 plus finishing

When replacement makes more sense

Replacement becomes the better option when decay has spread into the mortice and tenon joints that hold the door together, when the door has twisted so far it cannot close flat, or when it is so thin or weak that it cannot take a decent multipoint lock. Thin softwood doors from the 1970s and 1980s often fall into this group.

It also makes sense if you want a big improvement in warmth or security that the old door cannot provide. A new insulated timber door set can meet current thermal standards, while an old single-glazed door cannot, however well it is repaired. If the frame and sill are also failing, a full door set avoids paying twice.

Keeping a repaired door in good shape

A repair only lasts if the cause is dealt with. Make sure the sill has a drip so water falls clear, the bottom rail has a weatherboard where exposed, and the finish covers every face and edge, including the top and bottom. Microporous paints and stains let moisture escape while keeping rain out, and suit most external doors.

Check the door each spring and autumn. Touch in any chips, clear dirt from the threshold and drainage slots, and lubricate the lock. Small jobs done promptly stop rot getting a foothold and save the cost of bigger repairs later.

What a repair visit looks like

A typical overhaul starts with an inspection of the door, frame and sill, probing any suspect timber with a bradawl to find how far decay has spread. The joiner will then explain what can be saved and what cannot, and agree the work before starting. For simple easing and rehanging, the job is often done in a couple of hours with the door back in place the same day.

Splice repairs take longer, because glue and resin need time to cure and the repaired area has to be shaped and primed. Some joiners take the door to their workshop and fit a temporary board or spare door so the house stays secure. Others complete the repair on site over one or two visits. Either way, the door should go back with seals replaced, the lock lubricated and adjusted, and the repaired areas primed or finished. If the whole door needs refinishing, it is worth doing it at the same time so new and old timber are protected together and the colour matches across the door.

Questions people also ask

Can a rotten door frame be repaired?

Often, yes. Rot usually affects the foot of the frame and the sill. The decayed sections can be cut out and new timber spliced in, or a new sill fitted, while keeping the rest of the frame. If rot runs high up the jambs or the frame is loose in the wall, a new frame is usually better.

Why does my timber door stick in winter?

Timber takes up moisture in damp weather and swells, especially along any unsealed edges. Dropped hinges make it worse. The fix is to tighten or pack the hinges, plane the binding edge and seal it fully. Planing without resealing means the edge will swell again.

Is it worth repairing an old period front door?

Usually, yes. Original Victorian and Edwardian doors were often made from slow-grown timber that is denser than much modern stock. Splice and resin repairs, new seals and a fresh finish can keep them going for many more years, and on listed buildings repair is normally preferred to replacement.

Written and checked by the Timber Doors team. Read our editorial policy.

Get a free timber doors quote

Tell us what you need and we'll come back with a clear price.

Request a quote