Guide · Homeowners · 3 min read · Updated 17 November 2026
How to Refinish a Timber Door: Oils, Stains and Paints Explained
Short answer
To refinish a timber door, take it back to sound, clean wood, repair any damage, sand smooth, then apply a finish suited to the timber and exposure: microporous paint or stain for most external doors, hardwax oil for oak inside or on sheltered doors. Coat every face and edge. External doors typically need recoating every few years. Professional refinishing is included in repair and overhaul work costing £150–£450 per door.
Choosing the right finish
The best finish depends on the timber, where the door is and the look you want. External doors take sun, rain and temperature swings, so they need a finish that keeps water out while letting the wood breathe. Internal doors only need protection from wear and handling.
Microporous paints and stains are the usual choice outside. They flex as the timber moves and let moisture vapour escape, which reduces blistering and peeling. Oils bring out the grain of hardwoods but need more frequent topping up outdoors. Varnish forms a hard film that looks good at first but tends to crack and peel on external doors, letting water in behind it.
| Finish | Best for | Recoat outside |
|---|---|---|
| Microporous paint | Softwood and painted hardwood external doors | Every few years |
| Microporous translucent stain | Hardwood external doors showing grain | More often on sunny elevations |
| Exterior hardwax or decking-style oil | Oak and sapele on sheltered doors | Yearly top-up |
| Interior hardwax oil | Oak internal doors | Rarely, spot repair |
| Interior eggshell or satin paint | Painted internal doors | Only when worn |
Preparing the door
Preparation decides how long the new finish lasts. Where the existing coating is sound, a thorough clean and key sand is enough. Where it is flaking or cracked, it needs stripping back. Old doors may carry lead paint, so avoid dry sanding or burning off coatings you have not tested. A professional will use controlled stripping methods and dust extraction.
Once stripped, check for soft or dark areas, particularly along the bottom rail and around glazing beads. Cut out rot and splice or resin repair it before finishing. Fill open joints, refix loose beads and ease any edges that bind.
- Remove ironmongery or mask it carefully
- Take the door off its hinges if possible to reach the top and bottom edges
- Strip failing coatings back to sound wood
- Repair rot and fill defects
- Sand with the grain, finishing with a fine grit
- Remove all dust before the first coat
Applying the finish
Follow the manufacturer's system, which usually means a primer or base coat followed by two or more top coats. Work panel by panel in a set order, starting with the mouldings and panels, then the muntins and rails, and finally the stiles. This avoids lap marks and drips.
The top and bottom edges are the most neglected parts of any door and the most common entry point for moisture. Coat them as well as the faces. Leave each coat to dry fully, and lightly sand between coats if the system calls for it. Avoid finishing outdoors in cold, damp or very hot weather, because the coating may not cure properly.
Matching finish to timber species
Oak contains tannins that can react with iron and cause black staining, so use stainless or brass fixings and avoid wire wool. Oak and sapele both respond well to oils and translucent stains that show off their grain. Redwood and other softwoods are best painted outside, as they are softer and more prone to weathering.
Acetylated timber such as Accoya is very stable and takes paint well, which often means longer gaps between recoats. Whatever the species, choose a light colour on a south or west facing door if you can. Dark colours absorb more heat, which increases movement and shortens the life of the finish.
DIY or professional?
Refinishing an internal door is a manageable DIY job for most people. External doors are harder, because the door often has to be removed, rot repaired and the work done quickly so the house is not left open. Professional joiners and decorators can take a door off, repair and refinish it, and rehang it with new seals in one or two visits.
If your door has extensive rot, sticking problems or lock issues as well as a tired finish, it makes sense to combine everything into a single overhaul so the door is sound before the new coating goes on.
Mistakes that shorten a finish
Most early failures come down to a handful of mistakes. Painting over damp timber traps moisture, which pushes the coating off in blisters within months. Skipping primer on bare hardwood, especially oily species, leads to poor adhesion. Using interior paint on an external door, or mixing incompatible products from different systems, can cause cracking and flaking.
Leaving the top and bottom edges bare is the most common error of all, because nobody sees them. Water soaks in through the end grain, the door swells and the finish on the faces starts to lift. Applying coats too thickly in one go is another, as heavy coats skin over and stay soft underneath. Finally, rehanging the door before the finish has cured can mark it and stick it to the seals. Allow the full drying time on the tin, keep the door propped open slightly if you have to rehang it, and avoid closing it tight against fresh paint for the first day or two.
Questions people also ask
How often should an external timber door be refinished?
It depends on the finish, timber and exposure. A painted door on a sheltered elevation may last several years between coats, while a stained or oiled door facing south may need attention every year or two. Recoat when the surface starts to look dull or worn, before bare wood shows.
Can I paint over a varnished door?
Yes, if the varnish is sound. Clean it, sand it thoroughly to give a key, and use a suitable primer before painting. If the varnish is cracked or peeling, strip it back first, otherwise the paint will fail along with the old varnish beneath it.
Should I oil or stain an oak front door?
On a sheltered porch, oil gives a natural look and is easy to top up. On an exposed door, a microporous translucent stain usually lasts longer because it gives more protection from rain and sunlight. Both show off the grain, and both need regular maintenance outside.
Written and checked by the Timber Doors team. Read our editorial policy.
More guides
How Much Does a Timber Front Door Cost in the UK? 2026 Prices
A new hardwood front door leaf hung in a sound existing frame typically costs £900–£1,800 fitted in the UK in 2026, while a complete external timber…
Timber vs Composite Front Doors: Which Is Better for Your Home?
Choose timber if you want an authentic period look, a door made to any size or design, and one that can be repaired and refinished for decades.…
Timber Door Building Regulations UK: U-Values, Security and Glass
In England, a replacement external door in an existing home should meet a U-value of 1.4 W/m²K or better under Approved Document L. Glass in or…
Should You Repair or Replace a Timber Door? A Joiner's Checklist
Most timber doors can be repaired if the rot is limited to the bottom rail, the joints are still sound and the door is not badly twisted. A repair or…
Get a free timber doors quote
Tell us what you need and we'll come back with a clear price.
Request a quote